Happy-Go-Lucky Table Setting
Lots of triangles create the wow factor in this colorful tabletop trio. Fabrics are from the Textured Basics collection by Patty Young for Michael Miller Fabrics.
Materials for Place Mat, Coaster, and Napkin
Designer: Julie Herman of Jaybird Quilts
6-9x21" pieces (fat eighths) of dots in pink, green, and orange; and stripes in orange, aqua, and red (place mat and coaster tops, napkin binding)
1⁄2 yard cream tone-on-tone (place mat and coaster backings, napkin)
21" square lightweight batting
Finished place mat: 17-1⁄4x12"
Finished coaster: 7" diameter (point to point)
Finished napkin: 17" square
Yardages and cutting instructions are based on 42" of usable fabric width.
Measurements include 1⁄4" seam allowances. Sew with right sides together unless otherwise stated.Download this Project
Cut pieces in the following order. Click on "Download this Project" above for the triangle pattern. Designer Julie Herman used the Hex N More ruler from Jaybird Quilts to cut the 60° triangles from six 3-1⁄2x21" strips.
From each assorted dot and stripe, cut:
1-2x21" binding strip
From each pink dot, green dot, orange stripe, and aqua stripe, cut:
8 of Triangle Pattern
From each orange dot and red stripe, cut:
7 of Triangle Pattern
From cream tone-on-tone refer to Cutting Diagram to cut:
1-18x13" rectangle for place mat backing
1-17" square for napkin
1-8" square for coaster backing
From batting, cut:
Assemble Place Mat
1. Set aside one triangle from each dot and stripe for coaster.
2. Referring to Diagram 1, lay out remaining 40 triangles in four horizontal rows.
3. Pick up first two triangles in top row and place them right sides together (Diagram 2). Sew together triangles; press triangles and seam open.
4. Join next triangle in row to Step 3 unit (Diagram 3). Press open.
5. Continue adding triangles to make a row (Diagram 4). Press all triangles and seams open.
6. Repeat steps 1–3 to make four rows total (Diagram 5).
7. Sew together rows to make place mat top (Diagram 6). Press all seams open.
8. Referring to Diagram 7, trim 1⁄4" from place mat top points. The place mat top should be 17-3⁄4x12-1⁄2" including seam allowances.
9. Layer place mat top and cream tone-on-tone 18x13" backing rectangle with right sides together. Top backing rectangle with batting 18x13" rectangle (Diagram 8). Pin layers together.
10. Sew layers together 1⁄4" from place mat top edges, leaving a 6" opening along one long edge for turning (Diagram 9). Trim excess fabric and batting at corners. Trim at an angle across each corner.
11. Turn place mat right side out. Lightly press edges and hand-stitch opening closed to complete place mat.
12. Quilt as desired. Julie stitched in the ditch between each row.Download this Project
1. Referring to Diagram 10, lay out remaining six triangles (one from each dot and stripe).
2. Repeat Assemble Place Mat, steps 3 and 4, to make top row (Diagram 11). Repeat to make bottom row.
3. Sew together top and bottom rows to make coaster top (Diagram 12). Press seam open.
4. Referring to Assemble Place Mat, steps 9 and 10, layer coaster top, cream tone-on-tone 8" square, and batting 8" square; sew together, leaving a 2" opening for turning. Trim excess fabric and batting as done before.
5. Turn coaster right side out, press, and hand-stitch opening closed to complete coaster.
6. Quilt as desired. Julie stitched in the ditch between each triangle.Download this Project
1. Referring to Diagram 13, sew together six dot and stripe 2x21" strips, offsetting one end of each strip by 1-1⁄2", to make a strip set.
2. Using the 45° angle on an acrylic ruler, trim right-hand edge of strip set (Diagram 14).
3. Rotate strip set 180° (just-cut edge now is on the left).
4. Using the cut edge as a guide, cut six 2"-wide pieced strips (Diagram 15).
5. Using diagonal seams, join pieced strips into one binding strip. For a single-fold binding, which Julie used for this project, don't fold binding strip in half. Fold under 1" at one end of the binding strip and press. Using 1⁄2" seam allowance, stitch binding strip to right side of cream tone-on-tone 17" square. (Click on "Download this Project" above for details on turning corners.) When you return to the starting point, overlap the binding strip and finish sewing to the starting point. Turn binding over the edge to the back. Turn under raw edge 1⁄2" and hand-stitch in place.