Inspired by Tree Tops from designer Jocelyn Ueng of It’s Sew Emma 
Quilt tester: Jan Ragaller
2—18×21" pieces (fat quarter) assorted white prints (blocks)
3—18×21" pieces (fat quarter) assorted light blue prints (blocks)
3⁄4 yard navy blue stripe (blocks, border, binding)
3⁄8 yard gray print (blocks)
2—18×21" pieces (fat quarter) assorted blue prints (blocks)
3—9×21" pieces (fat eighth) assorted dark blue prints (blocks)
1-1⁄2 yards backing fabric
Finished quilt: 21-1⁄2×43-1⁄2"
Finished blocks: 12×20", 6×20"
Yardages and cutting instructions are based on 42" of usable fabric width.
Measurements include 1⁄4" seam allowances. Sew with right sides together unless otherwise stated.
Cut pieces in the following order.
From each white print, cut:
From each light blue print, cut:
From navy blue stripe, cut:
4—2-1⁄2×42" binding strips
5—2×42" strips for border
From gray print, cut:
From each blue print, cut:
From each dark blue print, cut:
Assemble Large Tree Blocks
1. Use a pencil to draw a diagonal line on wrong side of each white print 6-1⁄2" square. (To prevent fabric from stretching as you draw the lines, place 220-grit sandpaper under each square.)
2. Align a marked white print square with one end of an assorted light blue print 6-1⁄2×12-1⁄2" rectangle (Diagram 1; note direction of drawn line). Sew on marked line; trim seam allowances to 1⁄4". Press open attached triangle.
3. Align a matching marked white print square with opposite end of Step 2 rectangle (Diagram 1; again note direction of marked line). Stitch, trim, and press as before to make a large Flying Geese unit (Diagram 2). The unit should be 12-1⁄2×6-1⁄2" including seam allowances.
4. Repeat steps 2 and 3 to make six large Flying Geese units total.
5. Referring to Diagram 3, sew together two matching white print 2-1⁄2×5-1⁄2" rectangles and one navy blue stripe 21⁄2" square to make a large trunk unit. Press seams toward dark blue stripe square. The large trunk unit should be 12-1⁄2×2-1⁄2" including seam allowances. Repeat to make a second large trunk unit.
6. Referring to Diagram 4, sew together three large Flying Geese units and a large trunk unit with matching backgrounds to make a large tree block. Press seams toward top of block. The block should be 12-1⁄2×20-1⁄2" including seam allowances. Repeat with remaining Flying Geese units and large trunk unit to make a second large tree block.
Assemble Small Tree Blocks
1. Use a pencil to draw a diagonal line on wrong side of each gray print 3-1⁄2" square.
2. Referring to Assemble Large Tree Blocks, steps 2 and 3, use 12 marked gray print squares and blue print 3-1⁄2×6-1⁄2" rectangles to make six small blue Flying Geese units. Each unit should be 6-1⁄2×3-1⁄2" including seam allowances.
3. Repeat Step 2 using remaining marked gray print squares and the dark blue print 3-1⁄2×6-1⁄2" rectangles to make six small dark blue Flying Geese units.
4. Referring to Assemble Large Tree Blocks, Step 5, use gray print 1-1⁄2×3" rectangles and navy blue stripe 1-1⁄2" squares to make four small trunk units. Each unit should be 6-1⁄2×1-1⁄2" including seam allowances.
5. Referring to Diagram 5, sew together three small blue Flying Geese units, three small dark blue Flying Geese units, and two small trunk units to make a small tree block. Press seams toward top of block. The block should be 6-1⁄2×20-1⁄2" including seam allowances. Repeat to make a second small tree block.
Assemble Quilt Center
1. Referring to Quilt Assembly Diagram, lay out large tree blocks and small tree blocks in pairs.
2. Sew together block pairs. Press seams toward large tree blocks. Join pairs to make quilt center. Press seams toward top of quilt center. The quilt center should be 18-1⁄2×40-1⁄2" including seam allowances.
To make mitered corners in the border as shown in the featured wall hanging, complete the following steps.
1. Cut and piece navy blue stripe 2×42" strips to make:
2—2×54" border strips
2—2×32" border strips
2. Aligning midpoints, sew short border strips to short edges of quilt center, beginning and ending seams 1⁄4" from corners (Diagram 6). In the same manner, sew long border strips to remaining edges.
3. Referring to Diagram 7, lap one border strip over the other. Using the edge of an acrylic ruler, mark a diagonal line from border seam corner to intersection of strip raw edges. Then place bottom border strip on top and repeat marking process.
4. With right sides together, match marked seam lines and pin together (Diagram 8). Beginning with a backstitch at inside corner, sew strips together, stitching exactly on marked lines. Check right side to see that corner lies flat. Trim excess fabric, leaving a 1⁄4" seam allowance. Press seam open (Diagram 9).
5. Repeat steps 3 and 4 with remaining border corners to complete quilt top.
1. Layer quilt top, batting, and backing; baste. Quilt as desired.
2. Bind with navy blue stripe binding strips.