Inspired by Follow the Curves by designer Toby Lischko of Gateway Quilts & Stuff 
Quilt tester: Laura Boehnke
3/4 yard solid yellow (Pickle Dish blocks)
3/4 yard each of orange print and green print (Pickle Dish blocks)
1-1/4 yards mottled dark orange (Pickle Dish blocks, binding)
3/4 yard blue print (Pickle Dish blocks)
1 yard each of dark blue floral and red floral (Pickle Dish blocks)
1/2 yard each of blue floral and yellow floral (Lover's Knot blocks)
1/2 yard each of yellow print and red print (Lover's Knot blocks)
1-5/8 yards backing fabric
57" square batting
Lightweight tracing paper or other foundation material of your choice
Finished quilt: 48-1/2" square
Finished blocks: 12" square
Quantities are for 44/45"-wide, 100% cotton fabrics.
Measurements include 1/4" seam allowances. Sew with right sides together unless otherwise stated.
Cut pieces in the following order. Because the arc units are foundation-pieced, those fabric pieces are cut larger than necessary; you'll trim them to the correct sizes after stitching them to a foundation.
Click on "Download this Project" for Arc Foundation Pattern and patterns A-D. For tips on making templates of patterns A-D, click on "Download this Project" and refer to Make and Use Templates page. When making templates of the patterns, be sure to transfer dots marked on patterns to templates, then to fabric pieces. These dots are matching points and are used when joining pieces.
From solid yellow, cut:
From each orange print and green print, cut:
From mottled dark orange, cut:
5-2-1/2x42" binding strips
From blue print, cut:
12 of Pattern A
From each dark blue floral and red floral, cut:
12 of Pattern B
From each blue floral and yellow floral, cut:
8 of Pattern C
From each yellow print and red print, cut:
16 of Pattern D
Assemble Arc Units
Click on "Download this Project" for the Arc Foundation Pattern.
To foundation-piece, you stitch fabric pieces to foundation paper with the marked side of the paper facing up and the fabric pieces layered underneath. Each resulting pieced unit will be a mirror image of the foundation paper.
1. Use a pencil to trace the Arc Foundation Pattern 24 times onto lightweight tracing paper or other foundation material, tracing all lines and numbers. Cut out each traced pattern roughly 1/4" outside dashed lines to make 24 arc foundation papers.
2. Aligning 3" edges, layer a solid yellow 3x3-1/2" rectangle atop an orange print 3" square.
3. Place an arc foundation paper atop layered pieces, positioning it so that aligned edges are 1/4" beyond stitching line between positions 1 and 2 and at least 1/4" beyond arc's top and bottom stitching lines (Diagram 1). To check placement, pin on the line between positions 1 and 2. Flip orange print square open, making sure it completely covers position 2 and extends at least 1/4" into position 3. If it doesn't, reposition and recheck until it does.
4. Working with marked side of arc foundation paper up, sew on stitching line through all layers, extending stitching past beginning and end of the line by several stitches (Diagram 1).
5. Press orange print square open (Diagram 2). Trim orange print square to about 1/4" beyond the stitching line between positions 2 and 3 (Diagram 3).
6. Align a second solid yellow rectangle with trimmed orange print piece so their aligned edges are about 1/4" beyond stitching line between positions 2 and 3 (Diagram 4). Sew on stitching line. Press solid yellow rectangle open (Diagram 5). Trim positions 2 and 3 pieces about 1/4" beyond next stitching line.
7. Continue adding orange print squares and solid yellow rectangles, stitching and trimming in the same manner, until you have pieced the entire arc. Trim all fabric layers and foundation paper on dashed lines to make a yellow-and-orange arc unit (Diagram 6).
8. Repeat steps 2-7 to make 12 yellow-and-orange arc units total.
9. Using mottled dark orange 3x3-1/2" rectangles and green print 3" squares, repeat steps 2-7 to make 12 orange-and-green arc units (Diagram 7).
Assemble Pickle Dish Blocks
1. With right sides together, place a blue print A piece atop a yellow-and-orange arc unit; align marked dots at center and pin (Diagram 8). Pin pieces together at each end, then smooth blue print A piece along arc unit until edges are aligned. Pin approximately every 1/2", picking up only a few threads at a time (Diagram 9). Sew pieces together, removing each pin just before the needle reaches it. Press seam toward blue print A piece.
2. Referring to Diagram 10, align a red floral B piece with outer curved edge of Step 1 arc unit. Pin and stitch as in Step 1 to make a corner unit (Diagram 11). Press seam toward B piece.
3. Repeat steps 1 and 2 to make 12 corner units total.
4. Referring to Diagram 12, align a dark blue floral B piece with outer curved edge of an orange-and-green arc unit. Pin and stitch; press seam toward B piece.
5. Sew a mottled dark orange 2-1/2" square to each end of Step 4 unit. Press seams toward squares. Align inner curved edge of Step 4 unit with blue print A edge of a corner unit (Diagram 13). Pin edges and stitch as before to make a Pickle Dish block (Diagram 14). Press seam toward A piece. The block should be 12-1/2" square including seam allowances.
6. Repeat steps 4 and 5 to make 12 Pickle Dish blocks total.
Assemble Lover's Knot Blocks
1. Sew a blue floral 1-1/2" square to each end of a yellow print C piece to make a blue corner segment (Diagram 15). Press seams toward squares. Repeat to make eight blue corner segments total.
2. Sew together a yellow print C piece and a blue floral D piece (Diagram 16). Add a blue corner segment to opposite edge of D piece to make a blue block unit (Diagram 17). Press seams toward C pieces. The block unit should be 6-1/2" square including seam allowances. Repeat to make eight blue block units total.
3. Using yellow floral 1-1/2" squares, red print C pieces, and yellow floral D pieces, repeat steps 1 and 2 to make eight yellow block units total (Diagram 18).
4. Referring to Diagram 19, sew together two blue block units and two yellow block units in pairs. Press seams in opposite directions. Join pairs to make a Lover's Knot block. Press seam in one direction. The block should be 12-1/2" square including seam allowances. Repeat to make four Lover's Knot blocks total.
Assemble Quilt Top
1. Referring to Quilt Assembly Diagram, lay out Pickle Dish blocks and Lover's Knot blocks in four rows, noting placement and rotation of each block.
2. Sew together blocks in each row. Press seams in one direction, alternating direction with each row. Join rows to complete quilt top. Press seams in one direction.
1. Layer quilt top, batting, and backing; baste. Quilt as desired.
2. Bind with mottled dark orange binding strips.